-
$35.00
Renco 388 619-2S Rotary Encoder
-
$50.00
Anritsu K110-1-R Microstrip Sliding Contact (10 Contacts to a Case)
-
-
$100.00
GIGAVAC ELECTROMECHANICAL CONTACTOR MX-12 FB
COIL 48 VDC
1433
CAGE 3CKS7
-
$250.00
LSI LOGIC DUAL CHANNEL HBA LSI22320SE
SNP030723807
DUAL CHANNEL
HIGH BANDWIDTH SERIAL PCI EXPRESS HOST INTERFACE
-
$300.00
OPHIR PHOTONICS POWER SUPPLY NMS-NS2s-GR/9/5
POWER SUPPLY WITH CORD.
-
-
$1,700.00
Cable dressing fixture 307055-2
Trimmer tool 312317-1-A
Hand tool staker and locator kit for cable dressing and trimming
-
$375.00
NEWPORT OPTICAL POWER METER- MODEL 1830-C
- Compact, Full Featured, Benchtop Instrument
- 8 Decades of Signal Range
- Large, 4.5 Digit, Backlit, Wideview LCD
- Display Power in Watts or dBM
- Interfaces Newport Si, Ge, & InGaAs Detectors
- Optical Measurements from 190-1800nm
- Power Measurements from 100fW – 2W
- RS-232C and GPIB Built-In Interfaces
- The model 1830-c Power Meter is a high-resolution autoranging picoammeter compatible with all of Newport’s 818 Series low-power silicon, germanium and indium gallium arsenide detectors. I
-
$1,300.00
AGILENT KEYSIGHT HP OPTICAL ATTENUATOR
HIGH INPUT POWER LEVEL 2W
-
-
$125.00
VIGRA VS-10 SBUS COLOR FRAME BUFFER
-
$800.00
Ultra-compact transmissive SMD microsensor
10 AMP,
75V
3 Phase Mosfet bridge with intelligent integrated Gate Drive
The module is capable of 10 amps of output current and 75 volts of DC bus voltage.
It has a full line of protection features, including undervoltage lockout protection of the bias voltage, cross conduction control and a user programmabledeaad-time control for shoot-through elimination. In addition, the bridge may be shut down by using the ENABLE control.
FEATURES:
• 75 Volt Motor Supply Voltage
• 10 Amp Output Switch Capability, All N-Channel MOSFET Output Bridge
• 100% Duty Cycle High Side Conduction Capable
• Suitable for PWM Applications from DC to 100KHz
• Shoot-Through/Cross Conduction Protection
• Undervoltage Lockout Protection
• Programmable Dead-Time Control
• Low Active Enable for Bridge Shutdown Control
• Isolated Base Plate Design for High Voltage Isolation Plus Good Thermal TransferTYPICAL APPLICATIONS
• 3 Phase Brushless DC Servo Control Fin Actuator Control Gimbal Control
• 3 Phase AC Induction Motor Control HVAC Blower Control |
|
-
$675.00
USB-6211 OEM Data Acquisition Card DAQ USB
779676-011/0 16 Input 17 Bit 250KS/s
-
$1,600.00
The E 4413A diode power sensor, with wide dynamic range, is designed for use with the EPM and EPM-P series power meters for power measurements on CW signals from 50MHz to 26.6 GHz.
Features:
- Frequency Range: 50 MHz to 26.5 GHz
- Measurement range: 100 pW to 100 mW ( -70 dBm to +20 dBm)
- 50 ohm input impedance
- 3.5 mm (m) connector
- Calibration factors stored in EEPROM
- Compatible with the EPM and EPM-P series power meters
- Shipping Weight: 2 lb
-
-
$300.00
PROFESSIONAL CRIP TOOL IN EXCELLENT CONDITION
SMA 2201301-1
-
$300.00
Professional crimp tool in excellent condition.
Model 59980-1-0
-
$500.00
This 7-Slot LXI chassis allows any large number of 3U PXI modules to be installed and controlled through a standardized Ethernet interface.
Each of these modules are supported as though they are an LXI compliant device, complete with a driverless soft front panel that provides complete control of the module functions.
It is the buyer’s responsibility to verify compatibility before purchase.
-
$750.00
The Michigan Scientific S-series Slip Ring Assemblies are used for a variety of applications requiring up to 10 circuit connections. They are designed to mount on the end of a rotating shaft and make electrical connection to strain gauges, thermocouples, or other sensors. The slip ring brushes and rings are made of precious metals to minimize noise and enable the assemblies to be used for low-level instrumentation signals. In addition, a high grade stainless steel case provides protection from dust and other contaminants.